The Video Doorbell Pro is equipped with a PIR sensor that allows it to detect contrasting changes in the scenery, while using AI to process the images to determine if a motion alert is needed.

The amount of motion alerts you receive can be adjusted through the SimpliSafe® Mobile App and Web App Settings. There you can adjust the sensitivity to High, Medium, or Low. This will affect how much motion, and what sized objects will trigger a motion alert from your camera.

• High sensitivity will give you more frequent motion alerts

• Medium sensitivity is the default setting. You will receive a normal amount of notifications when using this setting

• Low sensitivity will give you fewer motion alerts

*Note, disabling motion alert notifications for your SimpliSafe® system will not turn off doorbell-press notifications.

You can change your settings in the mobile or web app using the steps below.

SimpliSafe® Mobile App

1. Open the SimpliSafe® App on your phone or tablet

2. Select the Cameras tab from the navigation bar at the bottom of the screen

3. Tap on the gear icon for Camera Settings in the upper right corner of the app

4. Select your Video Doorbell Pro from the list of Cameras

5. Choose Motion Detection

6. Adjust the sensitivity sliders, as needed

7. Once done, select Save in the upper right corner to save your selections

SimpliSafe® Web App

1. Login to your SimpliSafe® account using the Web App on a computer

1. If you manage multiple properties, choose the location you wish to update from the list by clicking on the Base Station Serial Number or Property Address

2. Select Devices from the left hand navigation menu

3. Click on your Video Doorbell Pro from the list of Cameras

4. A pop up menu will appear to the right hand side of the screen

5. Adjust the sensitivity slider, as needed

6. Once done, choose Save Changes from the bottom of the pop up to save your selections

If your Video Doorbell Pro is angled towards a high-traffic area, you may be able to resolve excessive motion events by adjusting the angle using the vertical angle bracket that was included in the box. If you require the ability to adjust your camera’s angle horizontally (side to side), a horizontal angle bracket can do the trick. Please contact our support team and request a Doorbell Angle Kit - free of charge!

This article will walk you through various scenarios where Wi-Fi troubleshooting may be needed to connect to and stream from your Smart Alarm Wireless Indoor Security Camera. You can scroll through the article, or click on one of the sections below to be taken directly to those steps:

• Trouble Connecting to Wi-Fi

• Red LED During Setup

• 'Connecting' Screen Times Out

• Poor Connectivity or Live Stream Quality

Trouble Connecting To Wi-Fi

You’ll want to make sure that you are connecting to a 2.4GHz (802.11b/g/n) network, as the Smart Alarm Indoor Camera can only connect to this network type. The indoor camera is not compatible with 5GHz networks. If your network shows up on the list of available Wi-Fi networks to connect to on the App, it is 2.4GHz compatible. For the best results, we recommend connecting to the same Wi-Fi network as your Base Station and having all of the devices within a short distance of each other if you are having trouble with the Finish Setup step.

Next, let’s test the Base Station connectivity. From the Keypad, establish a fresh connection between your Base Station and network by re-entering your Wi-Fi password. You’ll do this by going to Menu > Entering your Primary PIN > System Settings > Wi-Fi > Edit Network. Then confirm the connection was successful by accessing System Settings > Diagnostics > Wi-Fi and look for Internet: Reachable. If the test was unsuccessful, please check your router’s settings to confirm that it is working properly for other devices on your network.

If the Base Station test was successful, please try the following to reset your camera.

1. Press the tiny pinhole button down on the Smart Alarm camera for 1 second. This should do a soft reset on the camera

1. The small pinhole button can be found behind the larger setup button on top of the Smart Alarm Indoor Camera

2. Try the Finish Setup flow again by going to the Cameras tab, tapping on the camera you were setting up, and selecting Finish Setup.

   1. If the camera fails to set up when clicking Finish Setup, please remove the camera from your system using the Keypad

3. If the camera still will not add, hold down the larger pairing button on the Smart Alarm Indoor Camera for 10-20 seconds, or until it chimes and starts blinking white. This will factory reset the camera

4. Begin the device setup flow from the very beginning using the SimpliSafe® Mobile App

Red LED During Setup

A solid red LED on your Smart Alarm Indoor Camera during setup may indicate that the camera is too far from the Base Station. Please move the camera closer to the Base Station to complete the setup.

‘Connecting’ Screen Times Out

If you’re connecting your Smart Alarm Indoor Camera to the same network as your Base Station and the ‘Connecting’ screen times out or fails, we recommend attempting to connect one more time.

If that fails, exit the app and press the pinhole reset button on the top of the Smart Alarm Indoor Camera (the pinhole reset button can be found behind the larger setup button on top of the Smart Alarm Indoor Camera). Then return to the app, and on the Cameras page, find the camera you began to set up and finish the setup.

Poor Connectivity Or Live Stream Quality

We recommend performing a connection check for your Smart Alarm Indoor Camera in the SimpliSafe® App. You can find this using the following steps:

1. Open the SimpliSafe® app on your phone or tablet

2. Select the Cameras tab from the bottom navigation bar

3. Choose the gear icon for Camera Settings in the upper right corner of the app

4. Tap on your Smart Alarm Indoor Camera

5. Scroll down and choose ‘Connection Check’

6. Then, run the Connection Check by tapping on the ‘Start Connection Check’ button

You’ll want to ensure that your results meet our Wi-Fi requirements for cameras.

You can try moving the camera closer to your router to see if this helps your connectivity to see if that improves the connection speeds or alternatively, you can reduce the Picture Quality for your camera to use less bandwidth. To lower the Picture Quality, go to:

1. Open the SimpliSafe® app on your phone or tablet

2. Select the Camera tab from the bottom navigation bar

3. Choose the gear icon for Camera Settings in the upper right corner of the app

4. Tap on your Smart Alarm Indoor Camera

5. Scroll down and select Video Quality

6. Choose a new resolution

7. Test your camera feed afterward to see if the performance has improved

If your Smart Alarm Wireless Indoor Security Camera encounters an error that can’t be fixed through normal troubleshooting, resetting the camera to its factory settings may help.

Step 1: Remove the Camera From Your System

To reset your Smart Alarm Indoor Camera, we first recommend that you remove your camera from your system, if applicable. You can remove your camera from within the SimpliSafe® Mobile App using the following steps:

1. Go to the Cameras tab at the bottom of the SimpliSafe® Mobile App

2. Tap the gear icon in the top right corner of the app

3. Select your camera

4. Choose 'Remove Camera' at the bottom of the screen

5. Tap 'Yes' to remove the camera from your system

If you are seeing an error message within the SimpliSafe® Mobile App that says Unfinished Setup, you’ll need to remove this camera from the Keypad before proceeding.

1. Press the Menu button on your Keypad

2. Enter your Primary PIN

3. Scroll to devices and press Open on the right

4. Scroll down and locate the camera in question

5. Select your camera by pressing the arrow to the right

6. Choose Remove by pressing the arrow to the right to delete this camera from your system

Step 2: Resetting Your Smart Alarm Indoor Camera

After your camera has been removed from your system (if applicable) you can now reset the camera.

1. Press the tiny pinhole button on the Smart Alarm Indoor Camera for 2 seconds using a small item like the tip of a pen or a paperclip

1. The pinhole reset is located behind the setup button on the top of the camera (see image below)
   

2. Press and hold the Setup Button (the larger button on top of the camera) until the camera chimes, or about ~30 seconds.

1. Your camera should return to a flashing white status after performing this step. If there is no light at all, we recommend charging the battery and repeating these steps again at a later time

3. Once the camera is flashing white again, you can start the installation process for your Smart Alarm indoor Camera again within the SimpliSafe® Mobile App

Still Need Help?

If the status light on the front of the camera does not flash white and the battery has been fully charged, please contact our support team for additional troubleshooting.

If your camera had previously been set up but is now failing to connect to your Wi-Fi network, the Connection Check tool in the SimpliSafe® mobile app will tell you if there are any issues between your network and camera.

How to Run a Connection Check:

1. Open the SimpliSafe® mobile app

2. Tap on the Cameras tab on the bottom of the screen

3. Select the gear icon in the upper right corner

4. Choose your camera

5. Select Connection Check and follow the on-screen instructions to test your signal strength and upload speeds

Using your results, you can improve your camera’s connection with the tips below.

Camera Wi-Fi Requirements:

• Signal strength should be above -55dBm. A lower number means a weaker connection between your camera and Wi-Fi router.

  • If you have a low signal strength, try troubleshooting your Wi-Fi network

• Upload speeds need to be above 2Mpbs

  • If your upload speed is below 2Mbps, you may need to contact your Internet Service Provider (ISP) to upgrade your Internet package.

  • If your upload speed is exactly 2Mbps, you should take these steps to improve your upload speed.

The Smart Alarm Wireless Indoor Security Camera comes equipped with a passive infrared (PIR) sensor that allows it to sense contrasting temperature changes in its field of view, while also using Vision AI technology to determine if it should send you a motion alert.

If you are receiving too many motion alerts from your Smart Alarm Indoor Camera, there are placement, camera settings, and camera behavior changes you can make to decrease the amount of motion it captures.

Placement

We do not recommend placing your Smart Alarm Indoor Camera in an area where it faces a stairwell, window, or door, as it can pick up on excess motion. If your camera is facing any of those areas in your home, slightly adjust its placement so they are no longer in its field of view.

If you have any pets that the Smart Alarm Indoor Camera could pick up on, try moving the camera to a surface that’s at least 4 feet off the ground, angled straight out.

Camera Settings

There are additional settings you can change for your Smart Alarm Indoor Camera to help it detect fewer motion events.

Camera Behavior

You can configure your Smart Alarm to detect motion in each of the SimpliSafe® system’s armed modes: Off, Home, and Away. If your camera is consistently alerting you of motion in an armed state that you would not like it to, check to see if motion detection is turned on for your camera in that armed mode by taking the following steps:

1. Open up the SimpliSafe® Mobile App on your mobile device or tablet

2. Tap Cameras on the navigation bar at the bottom of the screen

3. Select the gear icon in the top right corner to open Camera Settings

4. Choose the Smart Alarm Indoor Camera you’d like to adjust

5. Under Camera Behavior, select the system’s armed mode that you do not want the Smart Alarm to detect motion in

6. Toggle Motion Detection off

Still Need Help?

If you’ve followed the steps above and your Smart Alarm Indoor Camera is still sending excess motion events, please contact our Support team for further troubleshooting.

Live stream delays can occur for a variety of reasons, most commonly stemming due to the camera’s “deep sleep” state it enters when not in use. When a live stream is initiated, the camera must first wake up and then connect to Wi-Fi to start the stream. This process can take up to 10 seconds.

If you are concerned about this delay or are experiencing a delay longer than 10 to 15 seconds, you can try the below steps to troubleshoot your camera’s Wi-Fi and system connectivity

• Move the Base Station closer to the camera

• Ensure your Base Station is connected to Wi-Fi

• Plug your camera into a continuous power source using the Outdoor Camera Power Cable. Doing this will enable performance mode, allowing your camera to remain awake and responsive

• Bring the camera and your internet router close together

• If the Camera works in this position, there may have been too great a distance between the devices and you will need to install the camera closer to your internet router

• You can also purchase a Wi-Fi extender to extend the range of your Wi-Fi

If the camera still does not connect when it is right next to your router, you may be experiencing Wi-Fi connectivity issues; in this case, you can try to troubleshoot your Wi-Fi connection.

What it Means

An "Unable to Stream Video" error means that the app was unable to download and display the streamable video. As this is likely an issue on the app end, our team is notified of these errors and investigates promptly to ensure your video is back up for streaming as soon as possible. You can try streaming this video again later.

Is There Anything I Can Do?

As mentioned above, this is likely due to an error on our end. However, in the meantime you can also check your Wi-Fi connectivity strength and speed as that can affect your camera's ability to stream and record video. This article explains the difference between connection strength and speed, as well as how to make sure both are working as they should to support your SimpliSafe system.

If the issue persists, please contact out customer support team. We'll be happy to help!